|
|
The Belch Bugger Electronic DIY Prank Kit
Makes Intermittent Belch Sounds!
This listing is for a FART BUGGER prank DIY electronics kit. You assemble this module on your own following the video instructions below! When assembled, this device makes 6x different Fart Sounds at different timing intervals ranging from 30 seconds to 18 minutes apart. The neat thing is that there are six messages and seven timing intervals, so the person you are pranking won't be able to pin-point timing. It comes with a small speaker that plugs directly into the main board, and a 9v connector that is soldered to the main board. The video above shows off all of the different Bugger flavours (Fart/Belch/Sex Noises/Swear Words); all of which are for sale in our store! Below, there are two videos. One is a functional video, and the other is an assembly and test video that goes through the entire assembly and test process, so that you can follow along! This kit does not come with a 9v battery, but you can find one at your local dollar store, or around the ol' homestead! A fully charged Duracell or Energizer battery should last at least a week and a half to two weeks. The sound quality is good, and the sounds are short and hard to pinpoint. We also sell these fully assembled and tested for a couple of dollars more, so check out our store!
WHAT YOU NEED TO DO:
When assembled, find a person (Friend/Enemy/Colleague/Family member) that you want to prank at either home or at work. Investigate the surroundings of where this person may spend most of their time. You have to be very clever as to where you put this device. IT MUST BE WELL HIDDEN! We've personally opened up cubicle walls and have placed these bad boys inside. The speaker can be taped to the inner wall of a cubicle facing the prank victim. Then, we just plugged in a battery, and put the cubicle back together. You can also put this under a bed, in the ceiling, in a pile or trash, etc. If you're feeling industrious, you can also consider opening up some consumer electronics to hide this module within. The possibilities are endless, but you have to be crafty, or else the person you're pranking will find it, and potentially get back at you!
Once you're done, just make sure that the battery is plugged in, and run away! Please note that it may not be the best idea to prank high strung people, or people who may want to get you into trouble for your pranking. Be wise, and be weary!
OPERATION:
Once you plug in your battery, all that you need to do to ensure that the device is working, is to wait 30 seconds. 30 seconds after power up, the device will trigger the first of 6x messages. From there, you can just let the device run on its own.
WHAT COMES WITH THIS KIT?
1) 1x Fart Bugger DIY electronics kit with speaker that plugs into the board, and a 9v battery connector. BATTERY IS NOT INCLUDED
SCROLL DOWN TO WATCH THE FUNCTIONAL AND ASSEMBLY VIDEOS!
SPECIFICATIONS:
Power Supply Voltage/Current: 9VDC @ >1mA (On board 5v regulator regulates power down to 5v).
Main Board Length: 67mm
Main Board Width: 21mm
Main Board Height: 11mm
MOUNTING:
There are four small mounding holes on the main board that you can choose to use if you wish. No mounding hardware is included.
WHAT YOU NEED TO DO:
When assembled, find a person (Friend/Enemy/Colleague/Family member) that you want to prank at either home or at work. Investigate the surroundings of where this person may spend most of their time. You have to be very clever as to where you put this device. IT MUST BE WELL HIDDEN! We've personally opened up cubicle walls and have placed these bad boys inside. The speaker can be taped to the inner wall of a cubicle facing the prank victim. Then, we just plugged in a battery, and put the cubicle back together. You can also put this under a bed, in the ceiling, in a pile or trash, etc. If you're feeling industrious, you can also consider opening up some consumer electronics to hide this module within. The possibilities are endless, but you have to be crafty, or else the person you're pranking will find it, and potentially get back at you!
Once you're done, just make sure that the battery is plugged in, and run away! Please note that it may not be the best idea to prank high strung people, or people who may want to get you into trouble for your pranking. Be wise, and be weary!
OPERATION:
Once you plug in your battery, all that you need to do to ensure that the device is working, is to wait 30 seconds. 30 seconds after power up, the device will trigger the first of 6x messages. From there, you can just let the device run on its own.
WHAT COMES WITH THIS KIT?
1) 1x Fart Bugger DIY electronics kit with speaker that plugs into the board, and a 9v battery connector. BATTERY IS NOT INCLUDED
SCROLL DOWN TO WATCH THE FUNCTIONAL AND ASSEMBLY VIDEOS!
SPECIFICATIONS:
Power Supply Voltage/Current: 9VDC @ >1mA (On board 5v regulator regulates power down to 5v).
Main Board Length: 67mm
Main Board Width: 21mm
Main Board Height: 11mm
MOUNTING:
There are four small mounding holes on the main board that you can choose to use if you wish. No mounding hardware is included.
The Bugger Functional Video: |
Assembly Video: |